What to do if your pipes burst.

guide home improvement how to how to use pipe insulation plumber plumber needed plumbing

Learn more about plumbing problems in this article.

What to do if your pipes burst.

How to handle busted pipes.

Ensure you have basic tools and know what to do in an emergency. A flexible hose connection or a push-fit pipe repair kit may fix a broken pipe. If not, a new pipe is required. Then empty the pipe completely before attempting to repair it. Fix a leaking pipe junction: Turn off the water, let it drain, then fix with putty.

Dry putty is easy to sand, smooth, and paint. When faced with this scenario, you must know your plumbing system and its valves. Your pipes may have been clogged with air after a drain and need to be refilled. An effective way to stop a ruptured water line is to use a pipe repair clamp. You may also use self-fusing repair tape to create a watertight seal.

Turn on all taps and flush all toilets to fix leaky cisterns and storage tanks. Untreated leaks may cause ceiling collapse. A blockage in the supply line from the cold cistern or hot water cylinder may cause a frozen faucet or sink. When the valve is kept open for extended periods of time, ice blocks the rising main. In order to thaw frozen pipes, start at the tap or valve and work your way down until water flows again.

Be prepared for the worst when unclogging a sink. Wear an apron, rubber gloves, and safety glasses. Plunging should only be done after a complete sink rinse. If you have a two-bowl sink, cover the other holes with a towel to help the plunger operate. Pour a bucket of warm water into the pan and repeatedly push the handle up and down to clear a small obstruction. A toilet auger extends and spins the probe around the U-bend, dislodging obstructions. After each usage, clean the auger with a bleach solution.

Find out how to detect, prevent, and fix common plumbing problems.

Water in your home may cause considerable damage, so fixing a plumbing issue as soon as possible is essential. Keep basic repair tools and materials in your toolbox, and know what to do in an emergency, and most issues will be contained.

How to fix a damaged water pipe permanently

This technique may be used to repair a burst pipe if the damaged section is 40-50 mm in length (see the manufacturer's instructions first). A push-fit pipe repair kit or a flexible hose connection may also be used to repair a damaged pipe. If not, you'll need to install a new pipe.

First and foremost, safety.

Plastic push-fit joints on copper pipes disrupt an earth bonding system's continuity. Connect the two copper pipes with a 4 mm2 single-core earth wire using two bonding clamps. This will reconnect the electrical wires.

Push-fit pipe repair kit.

Push-fit pipe repair kits are easy to use and may be put on either copper or plastic pipes. If your pipe is plastic, you must first put an insert (included in the package) into the pipe to assist maintain its form. Once the insert is in place, screw the plastic nut clockwise to tighten the fitting. The kit comes with comprehensive instructions.

You will need:

  • Pipe cutters, also known as pipe slices, cut pipes.
  • Junior hacksaws are little hacksaws.
  • Half-round file
  • Use steel wool or a deburring brush.
  • pliers for water pumps
  • Spanner with adjustable range
  • Push-fit pipe repair kit for 15mm or 22mm compression (straight) couplers, olives, and capnuts
  • PTFE ta

Steps to prepare supplies:

  • Turn off the water and thoroughly drain the pipe.
  • Second, remove the damaged pipe by cutting it on both sides using a tiny pipe cutter. You may need to unclamp the pipe from neighboring clamps to spin the cutter around it. If that fails, a hacksaw may be used.
  • Using a tiny half-round file and steel wool or a deburring brush, remove any paint, tarnish, or limescale from the copper pipe.
  • Remove the cap nuts and olives (metal rings) from the pipe coupling. Wrap PTFE tape around each compression joint thread five times clockwise. PTFE tape repels water and helps create a waterproof seal. To avoid unraveling when the nut is tightened, wrap the PTFE tape over the pipe thread in the other direction.
  • Finally, put the cut pipe ends into the burst pipe connection. Hold the coupler in place while tightening the nuts using an adjustable spanner.

How to repair a leaking pipe junction

Repairing a leaking soldered pipe junction requires skill, but using repair putty can permanently stop the leak and save time. After the putty has cured, sand, smooth, and paint it. You'll need these tools: Rubber gloves, cloth, and plumber's putty

Cut the power and water.

When a pipe bursts, a leak occurs, or flooding occurs, turn off the electricity at the fuse box. Inspect the sockets, switches, ceiling roses, and other electrical equipment for dryness once the leak has been repaired. If they have been submerged in water, do not re-energize them until they are totally dry. If you find yourself in this situation, you must know your plumbing system, including valve location, particularly the main stop valve, which allows you to shut off the water supply in an emergency or for repair purposes. Every few months, check valve accessibility to ensure they can be opened and closed easily. Applying penetrating oil or lubrication to the valve shaft may help it open. Never leave a valve completely open since this increases the chance of it seizing up and prevents you from closing it when you need to. Instead, shut the valve by a quarter-half turn.

Here's how to fix a leaky pipe junction:

  • Begin by turning off the water supply to the damaged pipe and letting it drain.
  • After completely drying the pipe, use a wire brush to fix the damaged region.
  • Wearing rubber gloves, twist or cut enough 2-part epoxy resin to finish the repair.
  • Work the material with your fingers until it is uniformly colored. You have about 5 minutes to finish this stage before the mixture begins to harden.
  • Gently push the repair putty around the joint, into the area between the pipe and fitting. It's a race against time. Smooth it out, but not too much.
  • After 24 hours, reconnect the water supply and check for leaks.

How to fix an airlock

It's conceivable that air got caught within your pipes after a drain and refill. Your faucets will splutter and, in some instances, stop working. A garden hose attached to the kitchen cold tap (or any other cold tap if you have a direct system) and the other end to the clogged faucet may assist. Turn on the broken faucet first, then the working faucet for a few minutes. If the mains pressure does not remove the air from the system, you may need to repeat the process many times. Turn off the faucets and wait a few minutes before re-using them. Remove the hose from the highest tap first, then the lowest, and so on. Remember to fully empty the hose before moving it outdoors.

Fixing a burst water line.

Using a pipe repair clamp to arrest a burst pipe is the quickest and most successful technique since it does not need the line to be emptied beforehand. Others just clamp over the burst area, while others screw on. Repair clamps, on the other hand, are just a temporary fix. Another option is to use self-fusing repair tape to produce a quick watertight closure. Here's everything you'll need and how to make it.

Steps to fix a burst water pipe:

  1. Remove any oil or dirt from the pipe on either side of the damaged region.
  2. Unroll the tape and cut around 20 cm of it using scissors. Discard the tape's backing. Once the backing tape is removed, you must work fast or the tape will not attach correctly.
  3. Double the length of the cut tape. Wrap the tape tightly around the pipe, beginning 30-40 mm away from the hole. Wrap the tape tightly around the item with a 50% overlap to ensure it bonds to itself.
  4. When you reach the damaged pipe, leave a gap (where the hole is) and wrap the tape over it to seal it. Continually wrap for 30-40 mm on the other side of the injury before turning around and reversing the tape. Hand-cover the hole this time. Always work with a tight 50% overlap on the tape.
  5. Keep moving back and forth until the damage is completely healed. Ensure that the tape's end bonds with the remainder of its length by pressing firmly on it.

How to deal with leaking cisterns and storage tanks.

Water cisterns and tanks are often located in the attic or on the second or third level of a home. As a result, if a leak occurs, water will pour through the ceiling. You must act quickly or the ceiling may collapse. Close the main door after disconnecting electricity and water from the main power switch and main stop valve. To finish the job, turn on all of the faucets and flush all of the toilets in the house. The pipelines and cold water storage cistern will be drained while the main stop valve is closed. The cistern itself may be leaking or overflowing due to problems with the ball valve or overflow. Pour out hot water cylinder, turn off the boiler and empty it by attaching a hose to the draincock at the bottom and sending it to an exterior gutter. Make any necessary repairs or replacements.

How to find out why a faucet isn't working.

It's annoying to wait when you turn on a faucet and nothing happens. Here's how to restore your water supply. 1st: Pour a few minutes, turn on the cold water faucet in your kitchen, or any other cold water faucet on a direct system. If no flow, make sure your main stop valve isn't closed. If the problem continues, call your water supplier. Assuming your cold water supply is working, examine the attic cold water storage tank. If it's empty, make sure the ball valve isn't jammed shut. Disassemble and clean or replace the valve. A blocked rising main, produced by ice in the winter, prevents flow when the valve is left open for long periods. Step 3 If your cold water storage cistern is full but your bathroom faucets are dry, there is probably an airlock or an obstruction in the supply line from the cold cistern or hot water cylinder.

Unfreeze a frozen pipe

Pipes in your loft, basement, garage, or anywhere else exposed to extremely low temperatures should be lagged to avoid burst and freezing. However, lagging will just delay the onset of freezing. If the temperature drops below freezing for a long time, ice may develop and clog your faucets and other outlets. In the worst situation, the ice may shatter your pipe or split a joint. As a consequence, if you intend to be gone for a long time during the winter, you should prepare. if you have a 'frost setting' on your thermostat, switch it on so that it automatically turns on if temps drop below freezing. You may also close the main cutoff valve to completely drain your system. An electric hair dryer may gradually reheat frozen pipes, beginning at the tap or valve and moving down its length until water flows again. As an alternative, soak hand towels in hot water, wring them dry, and wrap them over the pipe. But avoid using a blowtorch in your home since exposed flames offer a serious fire danger. Using a blowtorch on a frozen pipe may cause the water to boil and even explode.

How to unclog a blocked sink

If your sinks are draining slowly or not at all, there is probably a clog in the waste line. Slow draining plug holes are caused by a buildup of oil or fibers trapped below the plug hole grid. If the water does not drain at all, the drain pipe is fully blocked. The sections that follow will guide you through the different options for resolving the problem.

Prioritize safety first.

  1. Chemicals may splatter on your skin and cause chemical burns. Using a plunger should only be done after thoroughly rinsing your sink.
  2. You will need:
  3. Sink plunger
  4. clog-clearing auger
  5. Chemical drain cleaner
  6. Drain unblocker
  7. a towel, petroleum jelly, a bucket, bleach
  8. Requires safety eyewear

Before you start unblocking, prepare a backup plan.

  1. Unclogging a sink may be a nasty job, so be prepared for the worst. Wear an apron, rubber gloves, and safety eyewear to protect your clothes.
  2. Remove any visible debris from the sink and then take out the pop-up stopper if the drain is completely clogged. Fill it half-full of water and fasten it with a sink plunger's cup. Keep the pressure in the overflow using a damp cloth. If you have a two-bowl sink, cover the other sink holes with a cloth to provide enough pressure for the plunger to work effectively. Push the plunger up and down in the reservoir for 15–20 seconds. Remove the plunger and drain the water. This procedure may need to be repeated three or four times.
  3. If it doesn't work, try a chemical drain cleaner. Apply a thin coating of petroleum jelly around the rim of the plug hole to protect it. It is highly advised that you wear protective gloves and goggles while dealing with it. In locations with other chemicals like bleach, it is not advised due to the possibility of harmful vapors being released.
  4. If the blockage remains, the waste trap must be removed. Place a bucket underneath the trap to catch any spillage. Remove the trap and dump the contents into the bucket. Repair the trap, replacing any broken washers or O-rings. Avoid overtightening it as this will make subsequent undoing difficult. If this doesn't work, a drain auger may be used to probe the waste pipe.

Instant drain unblocker

An immediate drain unblocker uses a gas that expands when it touches water, producing strong turbulence that clears drains up to 20 meters away by agitation rather than pressure. Blocked drains are cleaned in a fraction of the time it takes to wash your hands. For blocked or slow-flowing sinks. Before using any product, always read and follow the packaging instructions.

How to unclog a blocked toilet

A blockage in the flushing mechanism allows the water to slowly rise to the rim. The pan exit is most likely blocked, but if not, the main drainage system may be faulty. You will need: Rubber gloves, bucket, bleach.

  1. To remove a minor blockage, try pouring a pail of warm water into the pan from a height.
  2. Place a large toilet plunger over the pan exit and repeatedly press the handle up and down.
  3. If it doesn't work, try a lavatory auger. Turning the handle extends and rotates the probe around the U-bend, dislodging the impediment.
  4. Wear protective gloves and read and follow the manufacturer's instructions. Remember to clean the auger with a bleach solution after each use.

Points to note How to handle busted pipes

  • Ensure you have basic tools and know what to do in an emergency.
  • A flexible hose connection or a push-fit pipe repair kit may fix a broken pipe.
  • If not, a new pipe is required.
  • Then empty the pipe completely before attempting to repair it.
  • Fix a leaking pipe junction: Turn off the water, let it drain, then fix with putty.
  • When faced with this scenario, you must know your plumbing system and its valves.
  • Your pipes may have been clogged with air after a drain and need to be refilled.
  • An effective way to stop a ruptured water line is to use a pipe repair clamp.
  • You may also use self-fusing repair tape to create a watertight seal.
  • Turn on all taps and flush all toilets to fix leaky cisterns and storage tanks.
  • A blockage in the supply line from the cold cistern or hot water cylinder may cause a frozen faucet or sink.
  • Be prepared for the worst when unclogging a sink.
  • Wear an apron, rubber gloves, and safety glasses.
  • Plunging should only be done after a complete sink rinse.
  • If you have a two-bowl sink, cover the other holes with a towel to help the plunger operate.
  • A toilet auger extends and spins the probe around the U-bend, dislodging obstructions.

Written by
BrookPad Team



Older Post Newer Post


Leave a comment

Please note, comments must be approved before they are published

Related Posts

Top 5 handheld shower heads in 2021
Top 5 handheld shower heads in 2021
What do you need to know about the finest handheld showers and what are the best ionic shower heads in 2021? Is it feasible to replace the shower head? What exactly is a shower head? When you turn on the shower, the shower head is the p...
Read More
The Art of Rest by Claudia Hammond
The Art of Rest by Claudia Hammond
How to Find Respite in the Modern Age Buy book - The Art of Rest by Claudia Hammond What is the subject of the book The Art of Rest? The Art of Rest (2019) is a documentary that takes an in-depth look at the realm of rest. The findings ...
Read More
Doughnut Economics by Kate Raworth
Doughnut Economics by Kate Raworth
Seven Ways to Think Like a 21st-Century Economist Buy book - Doughnut Economics by Kate Raworth What exactly is the subject of the Doughnut Economics book? Doughnut Economics (2017) is a call to arms for a new approach to economics that...
Read More
Food Fix by Dr. Mark Hyman
Food Fix by Dr. Mark Hyman
How to Save Our Health, Our Economy, Our Communities, and Our Planet – One Bite at a Time   Buy book - Food Fix by Dr. Mark Hyman What exactly is the subject of the Food Fix book? Food Fix (2020) demonstrates how some of the world's mos...
Read More
The Pegan Diet by Dr. Mark Hyman
The Pegan Diet by Dr. Mark Hyman
Combine Paleo and Vegan to Stay Fit, Happy and Healthy for Life Buy book - The Pegan Diet by Dr. Mark Hyman What is the subject of the book The Pegan Diet? The Pegan Diet (2021) is a straightforward, science-based approach to nutrition ...
Read More
A Brief History of Time by Stephen Hawking
A Brief History of Time by Stephen Hawking
From the Big Bang to Black Holes Buy book - A Brief History of Time by Stephen Hawking What is the subject of the book A Brief History of Time? Taking a look at both the history of scientific theory and the concepts that shape our curre...
Read More